Exactly How to Remove and Change a Bathtub.
Exactly How to Remove and Change a Bathtub.
Blog Article
Just how do you feel with regards to How to Install a Bathtub Yourself?
Setting up a tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably challenging project. If the old bathtub is easily available, the project can relocate immediately; if you have to open a wall surface to eliminate the old tub and place the new bathtub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub and embeded in the new one. Make certain you have certified on your own for the job and also are comfortable trying it. Instead of working with a professional to take control of a halfway-completed project, it is far better to consider using one before you start. Chances are you might need an expert plumber to make tube links.
This short article will certainly help you mount a new tub in your bathroom if you have actually currently purchased a brand-new tub as well as do not need to transform the arrangement of your previous water system pipelines.
Your tools as well as material checklist must consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain any water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the limited gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers remain in location between the faucet as well as the sink. Protect the tap in position with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap connectors. The former kind needs to be attached to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Tub
Utilizing the two wood boards under its feet, position the tub in the required position. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level as well as readjusting the feet on the tub until the level reads degree.
To set up faucets, fit the bottom of the outermost versatile tap port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water and examine all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub and additionally check the overflow electrical outlet and the regular outlet for leakages.
Finally, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling and also sealing around the tub needs to wait up until the bath tub has been utilized at the very least once as this will certainly settle it into its last position.
Getting ready for the Installment
Firstly, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its final position.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to split an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, resulting in problems with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water prior to sealing, to enable the movement experienced when the tub is in use. The sealer can fracture rather very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our piece about How to Install a Bathtub Yourself. Thank you so much for taking a few minutes to read through our piece. Enjoyed our piece? Please share it. Let other people discover it. Bless you for your time. Kindly check our website back soon.
Schedule Appointment Now Report this page